آی پی امداد
آی پی امداد
آریا الکترونیک parcham تکشو

آموزش ساختن حمام قلع بصورت ساده همرا ه با تصویر و فیلم

sardarshams

VIP+ افتخاری
کاربر +vip پلاس
vip افتخاری
کاربر
2008-06-20
1,073
25,005
43
Azarbayjan-Miandoab
سلام
آموزش ساختن حمام قلع بصورت ساده همرا ه با تصویر و فیلم

Kada00%20konzerva.jpg


Then chop off the bottom of her that will be used as when the melt tin. Enough is 1-2cm height.

Kada01%20isjecena%20konzerva.jpg


The next step is to make the heater.
heater you need waiting wires. If you do not take some old heater from a heater, an old fan off ... and roll 1m wire. Measure the resistance of her as you will need this information later.
before the budget should opt for another 2 parameters. Power peaks and voltage.
power my heater is 100W, I recommend that Neid below that because you will be waiting a very long time to melt the tin after switching.
adjust voltage source that you have. I have an adapter with regulation from 0-35V and I opted for a voltage of 30V.
calculation looks like this: U = 30 V P = 100 W rt = 28.6 ohms / m (resistance waiting wires per meter) Rt =? (Resistance heaters) Rt = U ^ 2 / P = 30 ^ 2/100 = 900/100 = 9 ohms heater wire length L = Rt / rt = 9 / 0.3 = 28.6 m If you have a count neda regulated power source. Simply take a piece of wire and waiting for pick up the heater voltage while they have brought to red heat. This method can be used to check the budget. The picture below is my heater. Wound on Borer 3m and stretched down to size.














Kada02%20grijac%20gol.jpg


Finished heater must somehow isolate the metal masses. I used ceramic beads taken from one heater oven.If you do not have them you can buy in the stores where they sell spare parts for kitchen appliances.
Kada03%20u%20perlicama.jpg


Earlier in the prepared tin must be in some way attached to the frame, I was punched in the middle and used a spacer to mount the PCB into the box. It can be a plain screw with two nuts.
Kada04%20konzerva%20probusena.jpg


Heater placed in the slot cans

Kada05%20grijac%20postavljen.jpg


The heater should be pressed with a tin and tin must be attached to a frame. I opted for the protective foil 12cm fan removed from the old PC power supply.
Kada06%20mrezica%20venta.jpg


Put-heater and attached to the grid

Kada07%20gotovo%201.jpg

Kada08%20gotovo%202.jpg


Assembled legs and ceramic chandelier clamps holding the heater running.

Kada09%20gotovo%203.jpg


Connected and commissioned. Pieces of tin melt.

Kada10%20ukljucena.jpg


In the next few pictures you will see desoldering process step by step.

Kada12%20princip%201.jpg

Kada13%20princip%202.jpg

Kada14%20princip%203.jpg

Kada15%20princip%204.jpg

Kada16%20princip%205.jpg

Kada17%20princip%206.jpg
News

Flip-flop of an ordinary relay v2

Schematic shows a simple way to make a flip-flop of an ordinary relay and several common components.Scheme, the rated voltage of 12 ..
more ...
Sound indication blinkers v2



Connecting single-phase motor



Universal Relay Driver








Facebook






Number of visits

Content View Hits : 751281





[hide]مشاهده فایل‌پیوست Broadcast Yourself_2.rar[/hide]
 

pcbh

کاربر
2012-04-04
88
496
با سلام و درود .
چند تا سوال داشتم .
1- چند ولت برق لازمه 220 یا 110
2- قوطی که استفاده کرده آیا می شود قوطی کنسرو هم جایگزین کرد .
3- مهره ها را از کجا تولید کنیم از هیتر برقی یا داخل بازار هست .
 

اقای مهندس

کاربران vip(افتخاری)
vip افتخاری
کاربر
2011-08-02
533
2,463
با سلام و درود .
چند تا سوال داشتم .
1- چند ولت برق لازمه 220 یا 110
2- قوطی که استفاده کرده آیا می شود قوطی کنسرو هم جایگزین کرد .
3- مهره ها را از کجا تولید کنیم از هیتر برقی یا داخل بازار هست .
سلام
مسلمه که باید 220 باشه
2- بله می شود .مهم اینه که بتواند حرارت بالا را تحما کند که قوطی های کنسرو مثل کنسرو ماهی جواب گوی کار شما هست
3-در بازار موجود هست .
 

farah676

VIP+ افتخاری
کاربر +vip پلاس
vip افتخاری
کاربر
2007-08-22
4,686
61,984
اصفهان
با عرض سلام

جناب شمس عزیز دو اشکال در این حمام وجود دارد ، اول اینکه قطع به بدنه خواهد چسبید و مورد دوم اینکه بسرعت سرد میشود ـ حوضچه از چدن باید باشد)
من یک نمونه کوچک را به مبلغ 40 تومان خریده ام و کار کرد بسیار خوبی دارد
 

پیوست‌ها

M_hezavian70

کاربر
2013-03-24
1
3
سلام.این حوضچه هارو از کجا باید خرید؟مصرف برقش چقدره؟من میخام کاری رو شروع کنم ک نیاز به لحیم کاری تو تیراژ بالا دارم.برد هام هم یکطرفه هستن.استفاده از حوضچه بهترین روشه؟لطفا راهنماییم کنید.
 

ahmadkhalghi

کاربر
2015-05-10
1
0
سلام. ببخشید چطوری با دیمر میشه دماش رو کنترل کرد؟ دیمر رو کجا نصب کنم؟ دما می تونه تا 300 درجه سانتیگراد برسه؟
 

بهبود 68

VIP+ افتخاری
کاربر +vip پلاس
vip افتخاری
کاربر
2015-03-31
517
1,179
سلام. ببخشید چطوری با دیمر میشه دماش رو کنترل کرد؟ دیمر رو کجا نصب کنم؟ دما می تونه تا 300 درجه سانتیگراد برسه؟
با سلام
دوست عزیز شما میتونید از ترموستات نصب شده روی اتوی لوله کشی استفاده کنید.راست کار شماست
 

ajan

VIP+ افتخاری
کاربر
2012-12-21
515
1,472
ایران عزیزم
دوستان سلام


بیاید به کمک هم یک اتماتیک بسازیم کاری نداره به خدا همت می خواهد من یک عدد گازی ساخته ایم بزرگ هست

 
بالا